| Double Grip Drop Forged | Drop Forged | Malleable |
|
Meets
Design Requirements According to Federal Specification FFC 450D,
Type 3, Class 1 |
 Fig.391 |
The efficiency rating of a properly prepared termination for clip sizes 3/16 through 7/8 is 80%; sizes 1" through 1-1/2" is 90%. This rating is based on the catalog breaking strength of the wire rope. If pulley is used in turnback instead of thimble or if Seale construction or similar large outer wire type construction in 6x19 class is used in 1" and up, add 1 additional clip. If a greater number of clips are used than shown in the table, the amount of rope turnback should be increased proportionately. |
| Clip Size Inches | Minimum No. of Clips | Amount of Rope to Turn Back in Inches | Torque in Ft. Lbs. | Weight Per 100 (Lbs.) |
| 3/16 - 1/4 | 2 | 4 | 30 | 18.50 |
| 5/16 | 2 | 5 | 30 | 28 |
| 3/8 | 2 | 5-1/2 | 45 | 40 |
| 7/16 | 2 | 6-1/2 | 65 | 70 |
| 1/2 | 3 | 11 | 65 | 75 |
| 9/16 | 3 | 12-3/4 | 130 | 100 |
| 5/8 | 3 | 13-1/2 | 130 | 100 |
| 3/4 | 3 | 16 | 225 | 175 |
| 7/8 | 4 | 26 | 225 | 225 |
| 1 | 5 | 37 | 225 | 300 |
| 1-1/8 | 5 | 41 | 360 | 400 |
| 1-1/4 | 6 | 55 | 360 | 400 |
| 1-3/8 | 6 | 62 | 500 | 700 |
| 1-1/2 | 7 | 78 | 500 | 700 |
|
DO NOT EXCEED WORK LOAD LIMIT OR 20% OF THE PRODUCT'S BREAK STRENGTH. |
|
Meets
Design Requirements According to Federal Specification FFC 450D,
Type 1, Class 1 |
 Fig.392 |
The efficiency rating of a properly prepared termination for clip sizes 1/8 through 7/8 is 80%: sizes 1" through 3" is 90%. This is based on the catalog break strength of the wire rope. If pulley is used in turnback instead of thimble or if Seale construction or similar large outer wire type construction in 6x19 class is used in 1" and up, add additional clip. If a greater number of clips are used than shown in the table, the amount of rope turnback should be increased proportionately. |
| Clip Size Inches | Minimum No. of Clips | Amount of Rope to Turn Back in Inches | Torque in Ft. Lbs. | Weight Per 100 (Lbs.) |
| 1/8 | 2 | 3-1/4 | 4.5 | 6 |
| 3/16 | 2 | 3-3/4 | 7.5 | 10 |
| 1/4 | 2 | 4-3/4 | 15 | 20 |
| 5/16 | 2 | 5-1/4 | 30 | 30 |
| 3/8 | 2 | 6-1/2 | 45 | 47 |
| 7/16 | 2 | 7 | 65 | 76 |
| 1/2 | 3 | 11-1/2 | 65 | 80 |
| 9/16 | 3 | 12 | 95 | 104 |
| 5/8 | 3 | 12 | 95 | 106 |
| 3/4 | 4 | 18 | 130 | 150 |
| 7/8 | 4 | 19 | 225 | 212 |
| 1 | 5 | 26 | 225 | 260 |
| 1-1/8 | 6 | 34 | 225 | 290 |
| 1-1/4 | 7 | 44 | 360 | 430 |
| 1-3/8 | 7 | 44 | 360 | 460 |
| 1-1/2 | 8 | 54 | 360 | 540 |
| 1-5/8 | 8 | 58 | 430 | 700 |
| 1-3/4 | 8 | 61 | 590 | 925 |
| 2 | 8 | 71 | 750 | 1300 |
| 2-1/4 | 8 | 73 | 750 | 1600 |
| 2-1/2 | 9 | 84 | 750 | 1900 |
| 2-3/4 | 10 | 100 | 750 | 2300 |
| 3 | 10 | 106 | 1200 | 3100 |
|
DO NOT EXCEED WORK LOAD LIMIT OR 20% OF THE PRODUCT'S BREAK STRENGTH. |
|
Meets
Design Requirements According to Federal Specification FFC 450D,
Type 1, Class 2 |
 Fig.393 |
These clips are intended for use in making eye termination in right regular lay wire rope. Such an assembly is for non-critical light duty use where a small applied load is expected such as hand rails, fencing, guard lines, etc. For this reason an efficiency of the termination is not stated. If a greater number of clips are used than shown in the table, the amount of rope turnback should be increased proportionately. |
| Clip Size Inches | Minimum No. of Clips | Amount of Rope to Turn Back in Inches | Torque in Ft. Lbs. | Weight Per 100 (Lbs.) |
| 1/8 | 3 | 4-3/4 | 3.0 | 4 |
| 3/16 | 3 | 5-1/2 | 4.5 | 7.5 |
| 1/4 | 3 | 7 | 15 | 13 |
| 5/16 | 3 | 7-3/4 | 15 | 15 |
| 3/8 | 3 | 9-1/2 | 30 | 22 |
| 7/16 | 3 | 10-1/4 | 40 | 27 |
| 1/2 | 4 | 15-1/4 | 45 | 37 |
| 9/16 | 4 | 16 | 50 | 52 |
| 5/8 | 4 | 16 | 75 | 58 |
| 3/4 | 5 | 22-1/4 | 75 | 85 |
| 7/8 | 5 | 23-1/2 | 130 | 128 |
| 1 | 6 | 31 | 130 | 150 |
| 1-1/8 | 7 | 39-1/2 | 200 | 260 |
| 1-1/4 | 8 | 50 | 200 | 300 |
| 1-3/8 | 8 | 50 | 360 | 452 |
| 1-1/2 | 9 | 60-1/2 | 360 | 490 |
|
DO NOT EXCEED WORK LOAD LIMIT OR 20% OF THE PRODUCT'S BREAK STRENGTH. |
